To move a hot tub, disconnect the power (hardwired tubs need an electrician), drain all 300 to 500 gallons completely, then remove the cover and accessories. Use two heavy-duty dollies and ratchet straps to roll it along a plywood path, and plan for 4 to 6 people plus a flat-bed truck or trailer rated for the weight.
A hot tub is one of the heaviest, most awkward things a homeowner will ever try to relocate. Empty, most weigh 500 to 1,000 lbs, and larger models push past 1,200 lbs. There are no good handholds, the shape fights you at every turn, and the shell cracks if you handle it wrong. The good news: with the right planning, equipment, and crew, learning how to move a hot tub safely is realistic for many people. This guide walks through the full process from property to property, and most of these steps apply to repositioning a tub on the same property too.
Hot Tub Moving Equipment You'll Need
Gather everything before move day. Stopping halfway to find another strap or a wider board is how tubs get dropped. The list of hot tub moving equipment needed covers two categories: gear and crew.
- Two heavy-duty four-wheeled furniture dollies, each rated 1,000 lbs or more
- At least four ratchet straps
- 4×4 lumber boards and plywood sheets for a rolling path over soft ground
- Moving blankets to protect the shell and cabinet
- A submersible pump or garden hose for draining
- A wet/dry vacuum to clear residual water from the lines
- A pipe wrench if you need to disconnect plumbing fittings
- A flat-bed truck or trailer rated to handle the full weight
- A loading ramp, ideally two
Crew matters as much as gear. For a standard 7'×7' tub, you want a minimum of four capable adults. Step up to six for larger models (8'×8' and up) or any route with inclines. Assign roles before you lift anything: two people on the dollies, one directing, one spotting the ramp. Everyone should know the plan before the tub leaves the ground.
Step 1: Disconnect the Power
Kill the power at the main breaker first, not just the switch on the tub. Most hot tubs are hardwired into a dedicated circuit, and a hardwired tub needs a licensed electrician to disconnect it properly. Do not skip this. Working on live high-amperage wiring is a serious hazard, and a sloppy disconnect makes reconnection at the new spot far harder.
Before the wires come loose, photograph the wiring so reconnection is straightforward later. Check your local electrical code as well. Some jurisdictions require a permit for the disconnect and reconnect, and it's much easier to handle that paperwork up front than after the tub is already on the truck.
Step 2: Drain the Hot Tub Completely
Learning how to drain a hot tub for moving is the step most people underestimate. A standard tub holds 300 to 500 gallons. A gravity drain through the valve takes two to four hours, while a submersible pump cuts that to 30 to 60 minutes. Find the drain valve, usually near the base panel where the access cabinet is, and connect your hose there.
Direct the water well away from your foundation and lawn. Several hundred gallons dumped against the house can flood a basement or erode a flower bed. Once the bulk is out, run a wet/dry vacuum through the jets and lines to pull residual water from the plumbing. A few hidden gallons add real sloshing weight, and that shifting water can crack the shell when the tub tilts onto its dollies.
In Winnipeg, drainage is even more important. Water left in the lines through a winter move can freeze and split the plumbing or the shell. If you're moving a tub in Manitoba's cold months, drain thoroughly, vac the lines twice, and keep the time between stops as short as you can.
Step 3: Remove Accessories and Measure the Route
Take off the cover and store it separately, since covers tear and crease easily when they're under straps. Remove the steps and any side access panels that detach cleanly. Then measure: most tubs run 7'×7' or 7'×8' and stand 36 to 38 inches tall.
Now walk the entire route with a tape measure. Check every gate, doorway, tight corner, and slope between the tub and the truck. If any gate or passage is under 48 inches wide, plan to remove the gate or a fence panel ahead of time. Confirm the tub will fit your truck bed or trailer before move day, not while four people are holding it. Lay plywood sheets over grass, gravel, or any soft surface to build a stable rolling path the dollies won't sink into.
Step 4: Get the Tub on Dollies
With four people, gently tilt the tub to one side. Use your 4×4 boards as levers rather than gripping the bare shell edge, which can crack under that kind of point load. Slide the first dolly underneath, then tilt the other direction and slide the second dolly in. Center the weight evenly across both dollies before you let the tub settle.
Secure it with ratchet straps over the top and cinched down to the dolly frames before anyone lets go. Then test it: rock the tub slightly on the dollies to confirm it's balanced and the straps are holding. A tub that wobbles now will be a disaster on the move.
Step 5: Move It
Go slow and deliberate. One person calls every direction while everyone else keeps their full attention on their grip and footing. On your prepared plywood path or bare concrete, the dollies roll with moderate, steady effort.
At the truck, use two ramps side by side, one under each dolly. Never tilt the whole tub onto a single ramp. For transport, many tubs ride on their side, though some manufacturers specify an orientation in the manual, so check yours before loading. Once the tub is in the truck, re-strap it to the bed's anchor points. It must not shift in transit, where a sliding 800-lb tub can damage itself, the truck, and anyone nearby.
When You Should Call Professional Hot Tub Movers
An honest DIY guide has to name its limits. Some hot tub moves go outside weekend-project territory and into genuine risk. Call in a crew when any of these apply:
- The route involves more than two steps or any staircase
- A slope steeper than 10 degrees sits in the path
- Access requires a crane or a lift over a fence or structure
- A gate or passage is under 48 inches wide with no way to widen it
- The tub is oversized, more than 1,000 lbs empty, or an unusual shape
- You can't safely round up four or more capable adults
- The move is long-distance
There's also the warranty question. Some hot tub manufacturers void the warranty if the tub is moved without a certified technician, so check your warranty documents before committing to DIY. If your move involves any of these conditions, the safest decision is to bring in professional hot tub movers, a team with the specialized equipment and liability coverage to protect both the tub and your property.
After the Move: Reinstallation Checklist
Position the tub on a level, load-bearing surface, such as a concrete pad, an engineered deck, or a spa-rated base. Level it in multiple directions and shim where needed, following the manufacturer's specs. In Winnipeg, keep in mind that concrete pads can shift from frost heave, so check the level again after the first winter.
Reconnect the plumbing and inspect every fitting before you add water. Have your electrician reconnect the power and test the GFCI breaker before anyone uses the tub. Fill it, run the system for 15 to 30 minutes, and watch for leaks before the first soak.
Frequently Asked Questions
Can I move a hot tub by myself?
No, not solo. A standard tub needs at least four adults, and larger models or routes with inclines need six. The weight and awkward shape make a one-person move unsafe and likely to damage the tub. You can lead the project yourself, but you need a crew on move day.
How do you drain a hot tub before moving it?
Connect a hose to the drain valve near the base panel and let it gravity-drain, or use a submersible pump to speed it up. Direct the water away from your foundation. After draining, run a wet/dry vacuum through the jets and lines to remove residual water that adds weight and can crack the shell.
What equipment do you need to move a hot tub?
You need two heavy-duty four-wheeled dollies rated 1,000 lbs or more, at least four ratchet straps, 4×4 boards and plywood for the path, moving blankets, a pump or hose, a wet/dry vac, and a flat-bed truck or trailer with a loading ramp.
How many people does it take to move a hot tub?
Four capable adults is the minimum for a standard 7'×7' tub. Plan for six people if you have a larger model, a route with slopes or steps, or a tight access path. Assign clear roles before you start.
How much does it cost to move a hot tub?
A professional local hot tub move generally runs in the range of $300 to $1,200, depending on the tub size, access difficulty, and distance. A DIY move costs less in cash but adds equipment rental, truck rental, and the risk of an expensive crack or injury.
Can a hot tub be moved on its side?
Often, yes. Many tubs are transported on their side to fit the truck and stabilize the load, but some manufacturers specify a required orientation. Check your model's manual before loading, and always pad the side that rests against the truck bed.
Does moving a hot tub void the warranty?
It can. Some manufacturers void the warranty if the tub is moved without a certified technician. Read your warranty documentation before deciding on a DIY move, since the cost of lost coverage may outweigh what you save.
How do I move a hot tub through a gate?
Measure the gate first. If it's under 48 inches wide, plan to remove the gate or a fence panel before move day. Lay plywood through the opening for a smooth rolling surface, and keep one person spotting each side as the dollies pass through.
Need Help Moving Your Hot Tub in Winnipeg?
If this checklist has you second-guessing the DIY approach, that's completely reasonable, since hot tubs are unforgiving when something goes wrong mid-move. Our crew handles hot tub moves across Winnipeg with the right equipment and the experience to get yours where it needs to go. Call (204) 296-2223 for a free, no-obligation quote, or request an estimate online.



